What are the methods and principles of using pneumatic mixers?
1. How to use the pneumatic mixer: turn on the lifting switch, put the bucket into the bucket and drop the lifting switch, start stirring and mixing is completed, turn on the lifting switch, take out the bucket
2. Matters needing attention: The matters to be noticed in the cylinder lifting method are: the switch must first rise, stop after, and then fall down to avoid the idling mixer as much as possible. When testing the machine, try to bring materials to test, so as to ensure the balance effect and not hurt When the air horse air motor is used, it must be lubricated.
1. Determine the steering, torque and speed before use, and it is strictly prohibited to adjust during rotation.
2. Do not touch the pneumatic mixer head with hard objects during use.
3. Handle gently during use and do not bump.
4. Regular inspection and maintenance; keep the surface clean.
5. Be careful when replacing the batch head, not to damage other mechanical parts.
Pneumatic motor 6. Before long-term use of pneumatic mixer, it must be lubricated with oil and stored, otherwise the pneumatic mixer will cause embroidering damage. Used to lubricate and save before work.
7. Before using the manual oiler to lubricate, disconnect the pneumatic mixer and the air pressure tube, then add the lubricating oil (# 30- # 60) to the intake nut, connect the pneumatic mixer and the air pressure tube, and press the pressure handle switch to idle Lubrication and storage can be completed in about two seconds. 1-2 times a day can extend tool life.
8. Keep the air source clean and free of water. Before starting work on each shift, the water collector must be checked and drained. After work, the pneumatic mixer should be removed and lubricated and placed in the tool cabinet. It is strictly forbidden to drain with an air mixer.
1. Maintain the air quality of the intake side of the motor (dry, clean, with oil mist)
2. The best service life and performance need to drop 1-2 drops of special oil for pneumatic tools in each cubic air intake
3. Maintain the recommended maintenance cycle (short cycle maintenance for oil-free operation)
Pneumatic motor manufacturers 4. Use air supply pipes and pipe joints with sufficient internal diameter and triple parts of air source
5. The maximum length of the air supply pipe should not exceed 3 meters
6. Operate and use the motor near the rated power, speed and other parameters of the air motor is the best working interval
1. Small size, light weight, freely adjustable speed, better control of speed, compared with large size and heavy weight of the motor, the speed can be adjusted only by external governor
2. The rotational speed and torque of the air motor supporting reducer are relatively stable. For example, the pneumatic reducer motor in the rubber industry and the paper industry is applied for winding and stable when unwinding. More flexibility
3. Pneumatic stirring is used on the mixer in the chemical mixing industry. It can be explosion-proof. It does not touch the power supply when stirring, and all are driven by gas. Provides more flexibility than most standard electric reducers. Pneumatic reduction motor can provide infinitely adjustable rotating power. The torque is from 1 to 1500N.M. The reversing valve on the pipeline can make the motor pneumatically reversing instantly
4. More specifications and models for selection, air motor power selection, air motor speed selection
1. Use dry and clean compressed air. The pipeline system should be installed with an oil mist device and a gas-water separator (one size larger than the air inlet of the motor). The mist-like engine oil enters the motor with the compressed air. The lubricating oil is 20 # or 30. #Machinery oil
2. When the motor is used for the first time, 2.5Kg of 20 # or 30 # mechanical oil should be injected from the oil injection hole, and then 0.5Kg of oil should be added every shift. At the same time, the lubricator should be filled with oil, and the flow rate should be adjusted to 80 ~ 100 drops / minute Before the motor can start. After the motor is stored for a long time and starts without load, it should be idling for 0.5 to 1 minute under low pressure and lubrication conditions
3. After the normal use of the air motor for 3 ~ 6 months, disassemble it and check it once. If any worn parts are found during the cleaning process, they must be replaced.
4. Try to avoid the motor running at high speed without load
